View IK1589DOT_4584136.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TECHNICAL DATA 2.7 A Low Dropout Positive Regulator
IK1589
Description
The IK1589 is a low dropout three-terminal regulator with 2.7A output current capability. This device has been optimized for VTT bus termination, where transient response and minimum input voltage are critical. The IK1589 offers fixed 1.2V with 2.7A current capability for a GTL+ bus VTT termination. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload and ambient temperature that would create excessive junction temperatures. The IK1589 is available in the industry-standard TO-220, TO-263-3L, TO-263-2L and TO-252 (DPAK) power packages.
Features
* * * *
Output Current : 2.7 A Maximum Input Voltage : 7V Current Limiting and Thermal Protection Standard TO-220, TO-263, TO-252 (DPAK) power packages
Ordering Information IK1589KB TO-220 Tube IK1589DOT TO-252 T&R IK1589D2 TO-263 Tube IK1589D2T TO-263 T&R
Applications
* * *
A GTL + bus supply VRM 8.5 Low voltage logic supply Post regulator switching supply
Absolute Maximum Ratings (note1)
Parameter V IN Operating Junction Temperature Range Storage Temperature Range Lead Temperature (Soldering, 10 sec.) Power Dissipation (Note2) Internally Limited 0 -65 Min. Max. 7 155 150 300 Unit V C C C
Operating Ratings
Juncton Temperature Range (Note3) -10C to 125C
Rev. 01
IK1589
Electrical Characteristics
Typical and limits appearing in normal type apply Tj=+25C Symbol Vout Vout Vout V Ilimit Io(min) RR S Parameter Output voltage (Note 6) Line Regulation (Note 7) Load Regulation (Note 7) Dropout Voltage (Note 8) Current Limit Minimum Load Current Ripple Rejection Temperature Stability Conditions 3.3V Vin 7V (Vout + 1.5V) Vin 7V Iout = 10 mA (Vin - Vout) = 3V 10mA Iout 2.7A Vref=1%, Iout = 2.7A (Vin-Vout) = 2V 1.5V (Vin-Vout) 5.75V f RIPLE = 120HZ, COUT=25F Tantalum, Iout=5A;V I N =Vout+2V 60 0.5 4.5 10 Min (Note5) 1.176 Typ (Note4) 1.200 Max (Note5) 1.224 0.2 1.5 1.3 Units V % % V A mA dB %
NOTES 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Rating indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. NOTES 2: Power Dissipation is kept in a safe range by current limiting circuitry. NOTES 3: The maximum power dissipation is a function of Tj (MAX), jA and T A . The maximum allowable power dissipation at any ambient temperature is PD=(Tj(MAX) - T A)jA. NOTES 4: Typical Values represent the most likely parametric norm NOTES 5: All limits are guaranteed by testing or statistical analysis NOTES 6: IFULL LOAD is defind in the current limit curves . The IFULL LOAD curve defines the current limit as a function of input-to-output voltage . NOTES 7: Load and Line regulation are measured at constant junction temperature , and are guaranteed up to the maximum power dissipation of 30W.Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. NOTES 8: Dropout voltage is specified over the full output current range of the device.
Typical Application
Rev. 01
IK1589
Typical Performance Characteristics
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Rev. 01
IK1589
Applications Information General
The IK1589 is a three-terminal regulator optimized for a GTL+ VTT termination applications. It is short-circuit protected, and offers thermal shutdown to turn off the regulator when the junction temperature exceeds about 150C. The IK1589 provides low dropout voltage and fast transient response. Frequency compensation uses capacitors with low ESR while still maintaining stability. This is critical in addressing the needs of low voltage high speed microprocessor buses like a GTL+.
Stability
The IK1589 requires an output capacitor as a part of the frequency compensation. It is recommended to use a 22F solid tantalum or a 100F aluminum electrolytic on the output to ensure stability. The frequency compensation of these devices optimizes the frequency response with low ESR capacitors. In general, it is suggested to use capacitors with an ESR of <1.
Protection Diodes
In normal operation, the IK1589 does not require any protection diodes. A protection diode between the input and output pins is usually not needed. An internal diode between the input and output pins on the IK1589 can handle microsecond surge currents of 50A to 100A. Even with large value output capacitors it is difficult to obtain those values of surge currents in normal operation. Only with large values of output capacitance, such as 1000 F to 5000 F, and with the input pin instantaneously shorted to ground can damage occur. A crowbar circuit at the input can generate those levels of current; a diode from output to input is then recommended, as shown in Figure 7. Usually, normal power supply cycling or system "hot plugging and unplugging" will not generate current large enough to do any damage. As with any IC regulator, exceeding the maximum input-tooutput voltage differential causes the internal transistors to break down and none of the protection circuitry is then functional.
Figure 7. Optional Protection
Load Regulation
It is not possible to provide true remote load sensing because the IK1589 is a three-terminal device. Load regulation is limited by the resistance of the wire connecting the regulators to the load. Load regulation per the data sheet specification is measured at the bottom of the package. For fixed voltage devices, negative side sensing is a true Kelvin connection with the ground pin of the device returned to the negative side of the load. This is illustrated in Figure 8.
Rev. 01
IK1589
Figure 8. Connection for Best Load Regulation
Thermal Considerations
The IK1589 protects itself under overload conditions with internal power and thermal limiting circuitry. However, for normal continuous load conditions, do not exceed maximum junction temperature ratings. It is important to consider all sources of thermal resistance from junction-to-ambient. These sources include the junction-to-case resistance, the case-to-heat sink interface resistance, and the heat sink resistance. Thermal resistance specifications have been developed to more accurately reflect device temperature and ensure safe operating temperatures. For example, look at using an IK1589 to generate 2.7A @ 1.2V 2% from a 3.3V source (3.2V to 3.6V). Assumptions: * VIN= 3.6V worst case * VOUT = 1.176V worst case * IOUT = 2.7A continuous * TA = 70C * Case-to-Ambient = 3C/W (assuming both a heatsink and a thermally conductive material) The power dissipation in this application is: PD = (VIN - VOUT) * (IOUT) = (3.6 - 1.18) * (2.7) = 6.53W From the specification table: TJ = TA + (PD) * (Case-to-Ambient + JC)= 70 + (6.53) * (3 + 3) = 109C The junction temperature is below the maximum rating. Junction-to-case thermal resistance is specified from the IC junction to the bottom of the case directly below the die. This is the lowest resistance path for heat flow. Proper mounting ensures the best thermal flow from this area of the package to the heat sink. Use of a thermally conductive material at the case-to-heat sink interface is recommended. Use a thermally conductive spacer if the case of the device must be electrically isolated and include its contribution to the total thermal resistance. The case of the IK1589 is directly connected to the output of the device.
Figure 9. Application Circuit (IK1589)
Rev. 01
IK1589
Rev. 01
IK1589
Rev. 01
IK1589
Rev. 01
IK1589
TO-263-2L PACKAGE OUTLINE DIMENSION
Rev. 01

▲Up To Search▲

Price & Availability of IK1589DOT

	To Download IK1589DOT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .